|
Step 1 |
|
|
Prepare stock 300mm long x 25m x
36mm, European Beech or similar easily worked timber would be a
good choice |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Step 2 |
|
|
On the 36mm face place your HOCK
spokeshave blade 10 mm from the edge and outline with fine
pencil |
|
| |
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Step 3 |
|
|
Next rout this area x 3.4~3.6mm
deep for a snug fit of your HOCK spoke shave blade |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
Step 4 |
|
|
Next Rout / remove the material
shown by 5mm deep |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Step 5 |
|
|
Drill the holes shown for the HOCK
spokeshave blade stems x 5.0mm diameter at 100mm centres |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
|
Step 6 |
|
|
Fit blade for snug and comfortable
fit (Not too tight as you will want to often remove the blade to
adjust depth of cut) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
 |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
Prepare a WEARING strip (Like
Brass or Jarrah or similar hard stock (The length = blade width
x 5mm.
On one edge bevel to 45 degrees as shown) |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
